Good Quality Plastic Welding - ZX5700 Hot Wedge Welding machine – Heatfounder
Good Quality Plastic Welding - ZX5700 Hot Wedge Welding machine – Heatfounder Detail:
Specifications:
Type | ZX5700 |
Power(W) | 3000W |
Voltage(V) | 220-230V |
Rate(Hz) | 50/60HZ |
Welding speed(m/min) | 0.5-4m/min |
Heating temperature(℃) | 20~600℃ |
Welding width | 15mmx2,interior cavity 15mm |
Condition | New |
Warranty | 1 Year |
Color | Green |
Packaging | Aluminum box |
Package size | 350x330x400mm |
Usage | For welding PE PVC and other hot melt materials |
Certificate | CE |
Thickness of material | 0.5mm-2.0mm |
Overlap width | 16cm |
Seam strength | ≥85% base material(tensile resistant in shear direction) |
Applications:
It can be applicable for welding PE、PVC、HDPE、EVA、PP and other hot melt material.
Notice:
- Unplug the tools before opening it to avoid of being hurt by exposed wires or component inside the machine with power
- Incorrect use of it can cause fire and explosion hazard because of high temperature, especially near combustible materials and explosive gases.
- Don’t touch heater tube and nozzle when they are hot. They may cause burns. Don’t point hot air flow in the direction of people or animals.
- The voltage rating stated on the welder must correspond to line/mains voltage (220V).
The drop cable / wire with protective earthed conductors can only be used.
- To ensure operator safety and reliable operation of equipment, the power supply must be installed power supply and leakage protection at the construction site.
- It must be running at the correct use of manipulation of the operator, or they may cause a fire or explosion caused by high temperature.
- Don’t use welder in the water, or on a muddy construction site, to avoid flooding, rain or moisture.
Please contact us for explosive view of the welding machine.
Welding process:
- Please lift the pressure handle (14) to separate the upper and down pressure roller (12), then plug the power and open the on power switch.
- Setting the welding parameters according to the data of welding test.
- Please wait the actual temperature value reaching the setting value.
- Put the welder at the welding position and put the two prepared materials (one up and the other one down) into the machine.
- Press the pressure handle (14) to make the upper and down pressure roller (12) in place. Then open the moving switch (31), the machine would start walking and welding automatically.
- To observe the relative position of the welding seam and the edge of the welded membrane at any time. It must be promptly corrected if there is deviation.
- When the welder walks into the end of material, the pressures handle needs to be lifted to separate the upper and down pressure roller in time.
- After completion of the welding work, press the buttons (24) and (25) on the panel to make the hot air blower in a cold blowing condition in order to cool the nozzle.
Product detail pictures:
Related Product Guide:
To regularly increase the management program by virtue from the rule of "sincerely, good religion and high quality are the base of enterprise development", we greatly absorb the essence of linked products internationally, and constantly produce new goods to satisfy the calls for of shoppers for Good Quality Plastic Welding - ZX5700 Hot Wedge Welding machine – Heatfounder, The product will supply to all over the world, such as: Canada, New Delhi, Kuwait, Furthermore, all of our products are manufactured with advanced equipment and strict QC procedures in order to ensure high quality. If you are interested in any of our products, please don't hesitate to contact us. We will do our best to meet your needs.
By Nina from Indonesia - 2015.02.21 12:14
The customer service reprersentative explained very detailed, service attitude is very good, reply is very timely and comprehensive, a happy communication! We hope to have a opportunity to cooperate.
By Janet from Sudan - 2015.12.05 13:53
Send your message to us:
Write your message here and send it to us